1. Firstly "step 2", sending M587 S"your-network-name" P"your-password" (with name and password substituted never returns an OK.
2. Continuing through the steps throws up this message: M552
   WiFi module is connected to access point , IP address 255.255.255.255
   ok. A green light comes on between the wifi antenna and SD card. However I cannot connect to the workbee through my browser (255.255.255.255 is not useful).

Please can you help?

Thanks

Incase it is useful here are some extra bits of info:

– – – – –

RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3

Executing config.g… HTTP is enabled on port 80

FTP is disabled

TELNET is disabled

Warning: Macro file config-override.g not found

Done!

RepRapFirmware for Duet 2 WiFi/Ethernet is up and running.

WiFi module started

WiFi reported error: Unexpected WiFi state ‘idlM552

– – – – –

M408 S5

{"axisMins":[0.00,0.00,0.00],"axisMaxes":[270.00,270.00,88.00],"accelerations":[150.00,150.00,150.00,150.00,500.00,500.00,500.00,500.00,500.00,500.00,250.00,250.00],"currents":[2400,2400,2400,2400,0,0,0,0,0,0,0,0],"firmwareElectronics":"Duet WiFi 1.02 or later","firmwareName":"RepRapFirmware for Duet 2 WiFi/Ethernet","firmwareVersion":"3.3","dwsVersion":"1.26","firmwareDate":"2021-06-15", "sysdir":"0:/sys/","idleCurrentFactor":100.0,"idleTimeout":30.0,"minFeedrates":[8.33,8.33,8.33,8.33,15.00,15.00,15.00,15.00,15.00,15.00,2.00,2.00],"maxFeedrates":[41.67,41.67,41.67,41.67,100.00,100.00,100.00,100.00,100.00,100.00,20.00,20.00]}

⟐ Answered April 18, 2023, 8:23 MST

⟐ Answered April 12, 2023, 8:04 MST

⟐ Answered April 11, 2023, 3:23 MST

Having tried different drill bits thickness' and speeds etc with no change, I am getting a bit lost as to what the problem is, although when watching it work, I noticed that the machine seems to have a bit of a judder when changing directions.

Once the job had completed, I turned it off and felt that their seems to be some give/wobble, whereby the wheels can move forward and backward by about 3mm, I have attached a video with sound below to show the movement.

Should the WorkBee have this kind of looseness to it? Should I tighten it somehow? I inherited this machine at my new work place (colleague who set it up has left over a year ago). I would appreciate any advice or link to a guide on getting the correct tension on this axis, and whether this could be impacting the accuracy of my router.

Thank you very much in advance anyone that can help!

Alistair

⟐ Commented April 06, 2023, 1:00 MST

To try to resolve this, I set up the job again in Fusion and ran a simulation, this appears to be fine.

I then had a look at the code in G Code viewer, which appears fine also and shows no glitches.

I have now run the job again and the same happened at the same point in the job?

Can anyone advise please as this is starting to make face twitch?

⟐ Commented April 04, 2023, 0:42 MST

⟐ Answered March 23, 2023, 0:50 MST

⟐ Answered March 17, 2023, 1:06 MST

Im in the installing process. Homing commands are working with all axis (z, x and y). But now I'm giving jogging command Y-50, and Y axis should move 50mm, but it's only moving 7mm. And Y-10 is moving only 1mm. Z and X axis commands are working correctly.

What is the problem and how can I fix this?

Thanks!

-Kimmo

⟐ Answered March 15, 2023, 7:32 MST

I recently fitted a Vevor air cooled motor and am wondering if the weight of it is on the border of what the motor can hold.

Also is there a solution for this?

Thanks

⟐ Commented March 10, 2023, 2:33 MST

Looking to surface spoilboard and struggling to work out speed feed and rates of overstep and depth to achieve this.

Using the Amana #45525 supplied.

Just need some direction as my calculations seem over the top.

Recommended settings would be appreciated to get going.

This is on 1500x1500 z+1

Many thanks for support

Rich

⟐ Answered March 06, 2023, 2:36 MST

I've been looking everywhere, but I cannot seem to find the source code for the workbee firmware/web interface, could someone point me to where I can download it?

⟐ Answer accepted February 28, 2023, 3:04 MST

⟐ Answered February 24, 2023, 0:39 MST

⟐ Answer accepted February 07, 2023, 6:55 MST

⟐ Answered February 06, 2023, 4:38 MST

Yesterday, my computer crashed, forcing me to have to completely download windows 12 again.

Part of the process is to completely remove all the Apps/Programs and settings from the laptop.

The problem I now have, is that all the original software that speaks to the machine is now gone.

To clarify, I don't mean the CNC software that designs the items, I mean anything that speaks to the machine itself.

I have gone onto Microsoft Edge and tried to connect via 'Workbee Local', however for some reason it just keeps timing out.

If I disconnect the cable the computer 'dings' so there is a connection.

I vaguely remember having to download a patch or something, but I don't remember what.

Can anyone help?

Regards

⟐ Answered February 02, 2023, 2:59 MST

any help much appreciated

⟐ Answered January 30, 2023, 1:44 MST

Is the overall base of the machine, A & C extrusions assembled, exactly 1500x1500?

Thank you

⟐ Commented January 30, 2023, 1:40 MST

⟐ Answered January 25, 2023, 1:49 MST

⟐ Commented January 12, 2023, 9:33 MST

this came up as I was setting it up ,anyone know what's wrong please

⟐ Answered January 05, 2023, 5:55 MST