My G Code Viewer is not previewing in google chrome?

Yesterday it was fine and i’ve changed nothing since , just tested in Microsoft edge browser and its working fine.

checking the chrome browser errors using f12 i get this

Failed to load resource: the server responded with a status of 404 (file not found)

``http://192.168.251.2/rr_download?name=0%...

vue.runtime.esm.js:1888 Error: WebGL not supported

is just strange chrome is saying not found but edge loads it?

Thanks

⟐ Commented September 05, 2022, 1:19 MST

I use Fusion 360 for design and tool paths, have two set ups but will not pause to allow for tool change. (750 belt workbee.)

⟐ Commented August 23, 2022, 0:26 MST

⟐ Commented January 04, 2022, 14:46 MST

does anyone have the original factory setup please that i could get.

⟐ Answer unaccepted December 20, 2021, 8:52 MST

I want to use a duet2 wifi on my cnc. I love to use my Keyboard/ xbox-controller / Jog-wheel for manually moving the CNC-head around.

Having Hardware Buttons and feedrate-encoder gives me freedom to focus on the machine rather than Looking on the Screen.

Is this supported by workbee firmware ?

Can I use Hardware Buttons or a Joystick to move the spindle around?

⟐ Answered April 19, 2021, 7:16 MST

I have had my work be for 4 years now and all has been good. Now having an issue when I upload a job and start an error message saying gcode file not found. i have been doing this same process on over 1000+ times but now it seems i keep getting this error.

Any idea what this error means and why it is happening

I have been using Cut2D Pro

⟐ Commented November 08, 2024, 1:49 MST

With MDF sitting on top of the extrusions on the base of the Workbee, there is little space for T-Tracks, without compromising height on the Z axis; also these make it difficult to get inserts into the T Track.

I appreciate there is probably no "correct" answer but any suggestions or recommendations would be most welcome! Thanks.

⟐ Commented September 10, 2024, 16:01 MST

Can anyone offer advice on what might be causing this issue and how it can be resolved?

Thanks!

⟐ Answered April 02, 2024, 2:14 MST

⟐ Answered October 16, 2023, 23:17 MST

I came into the workshop and turned everything on. I loaded up the control panel on my laptop and homed the CNC, everything was working fine. While setting up the machine, I noticed that I needed to make a change to the design. I left the workshop (as I work on my designs in the office) made the changes and went back to the workshop . when i arrived i noticed the connection had been lost to the control board.

I have tried to reconnect for the last 4 hours to no success. The laptop is showing that the ethernet is not connected. I have double checked the ethernet properties and they are fine. I have changed ethernet cable & tried a different laptop and still wont connect.

Really struggling to work out what to do next?

Any help would be grateful

Phill

⟐ Answered March 31, 2023, 0:00 MST

⟐ Commented January 27, 2023, 5:59 MST

I find myself doing a fair bit of experimenting on the machine, for example sneaking up on the right dimension for a hole.

This means that i tend to cancel jobs a lot, then upload a new version of the file and restart. As I have the large machine, this always takes a few minutes, because the machine goes back to the home position on pause/cancel.

Is there a way to change this behaviour? I’d love if I could overwrite the behaviour to only home z on pause/cancel.

Internally, it looks like duet runs pause.g/cancel.g, so if it’s possible to overwrite those, I figure that would solve the problem.

⟐ Answer accepted October 31, 2022, 16:36 MST

I don’t have wi-fi in my workshop so my laptop is connected to my workbee with an ethernet cable, but I now need to access the internet this way too. Do I just need to get an ethernet “splitter” (or USB adaptor) for my laptop to access both at the same time?

⟐ Commented February 10, 2022, 11:08 MST

Have screwed down and surfaced the spoiler board.

The work is secured down well to the board but I’m still getting a very noticeable difference in depth across the length of the cut ( x axis L to R)

any thoughts on why?

⟐ Answered November 19, 2021, 1:32 MST

I tried to run M552 in YAT:

WiFi module is connected to access point wt34a, IP address …......... <LF>ok<LF>WiFi reported error: Lost connection, auto reconnecting<LF>WiFi reported error: Timed out while trying to connect to wt34a<LF>WiFi module is connected to access point wt34a, IP address …...... <LF>

Then I tried to run M122 in YAT:

=== Diagnostics ===<LF>RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet WiFi 1.02 or later<LF>Board ID: 08DLM-996RU-N8PS0-7JKFG-3SJ6T-TBB7Q<LF>Used output buffers: 1 of 24 (11 max)<LF>=== RTOS ===<LF>Static ram: 25680<LF>Dynamic ram: 93348 of which 0 recycled<LF>Exception stack ram used: 308<LF>Never used ram: 11736<LF>Tasks: NETWORK(ready,816) HEAT(blocked,1236) MAIN(running,3796) IDLE(ready,160)<LF>Owned mutexes:<LF>=== Platform ===<LF>Last reset 00:11:47 ago, cause: power up<LF>Last software reset at 2020-09-28 13:04, reason: User, spinning module GCodes, available RAM 11676 bytes (slot 2)<LF>Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d<LF>Error status: 0<LF>Free file entries: 10<LF>SD card 0 detected, interface speed: 20.0MBytes/sec<LF>SD card longest block write time: 0.0ms, max retries 0<LF>MCU temperature: min 29.9, current 30.4, max 30.7<LF>Supply voltage: min 23.9, current 24.0, max 24.2, under voltage events: 0, over voltage events: 0, power

The strength of my wifi seems to be ok, when my laptop is standig ontop of the cnc it has no problems streamin movies an so on.

Any idear of where I made a mistake ?

⟐ Commented October 15, 2021, 1:37 MST

⟐ Commented September 23, 2021, 1:32 MST

⟐ Commented July 26, 2021, 1:04 MST

⟐ Commented May 20, 2021, 15:55 MST

⟐ Commented April 13, 2021, 7:02 MST

For example, If I have a piece of stock say 18mm thick can I use say a 30mm long End Mill with shaft of 6mm and cutting diameter of 6 mm and a cut depth of say 10 mm.

⟐ Answer accepted April 02, 2021, 16:30 MST