Ooznest - Active Questions

Touch probe set up in Machine Specific

Thu, 12 Nov 2020 09:21:39 -0700

Hi, trying to set up my touch probe. I have no tab to enable the touch probe on the machine specific page. Duet Web Control 2.0.7. The board is 1.02 and Duet WiFi Server Version 1.23. Not sure if that is all relevant, Iv just installed the machine and uploaded latest software version… I think, thanks for your help in advance…

⟐ Commented November 12, 2020, 9:21 MST

Web interface and z axis bottom out.

Tue, 10 Nov 2020 11:45:11 -0700

Hi, my 1500x1500 web interface has no work position settings, it has a temperature chart and extrusion control. When I’m sending a gcode the machine starts and runs however the Z axis would bottom out unless I cut the power-emergency stop. Thank you in advance for your support.

⟐ Answer accepted November 10, 2020, 11:45 MST

What RPM's correspond to which numbers on my router?

Thu, 22 Oct 2020 01:48:50 -0700

What RPM's correspond to which numbers on my router?

⟐ Answered October 22, 2020, 1:48 MST

X axis endstop always triggered

Wed, 21 Oct 2020 02:09:37 -0700

Hello,

I recently broke the X axis endstop when homing my machine, no clue why but it must have added extra steps, then popped the endstop away, and stopped.

It was not the first time homing the machine.

I did not change anything in the configuration files except what was asked during the setup process.

After installing a new endstop, purchased from you, it is still shown being triggered on the web interface.

Same thing happens when I unplug the endstop, still shown as triggered on the web interface.

I can’t home the X axis properly, as it stays in its current position and consider it has been homed.

If pin is damaged, could I switch the endstop to E0 or E1 as they are free ?

Thank you !

⟐ Commented October 21, 2020, 2:09 MST

Vibration and noise at idle

Fri, 16 Oct 2020 06:26:57 -0700

Hi, it appears that the motors keep producing noise after a movement has stopped. Particularly the Y motors. It is mostly noticeable when I press the emergency stop button and everything quiets down except the duet board fans. Is it a normal behavior ?

There is also a general vibration on the machine from the start-up, maybe due to the fans. Thanks.

Machine : workbee screw driven 1500x1500

⟐ Answer accepted October 16, 2020, 6:26 MST

Is the PanelDue compatible with the WorkBee Firmware?

Fri, 16 Oct 2020 00:31:35 -0700

Is the PanelDue compatible with the WorkBee Firmware?

⟐ Answer accepted October 16, 2020, 0:31 MST

How do I switch my Duet from Wifi to Access Point Mode Wifi?

Thu, 15 Oct 2020 11:50:22 -0700

How do I switch my Duet from Wifi to Access Point Mode Wifi?

⟐ Answer accepted October 15, 2020, 11:50 MST

My WorkBee does not home? It just moves away from the switch

Thu, 15 Oct 2020 11:48:44 -0700

My WorkBee does not home? It just moves away from the switch

⟐ Answer accepted October 15, 2020, 11:48 MST

The WorkBee has significant vibrating on the lead screws?

Thu, 15 Oct 2020 11:51:41 -0700

The WorkBee has significant vibrating on the lead screws?

⟐ Answer edited October 15, 2020, 11:51 MST

Can I add external buttons to the WorkBee CNC Machine?

Thu, 15 Oct 2020 11:45:33 -0700

Can I add external buttons to the WorkBee CNC Machine?

⟐ Answer accepted October 15, 2020, 11:45 MST

How do I switch a motor to the spare stepper driver output?

Thu, 15 Oct 2020 11:44:58 -0700

How do I switch a motor to the spare stepper driver output?

⟐ Answer accepted October 15, 2020, 11:44 MST

My Ethernet WorkBee is not connecting when plugged directly into a com

Thu, 15 Oct 2020 11:40:09 -0700

My Ethernet WorkBee is not connecting when plugged directly into a computer?

⟐ Answer accepted October 15, 2020, 11:40 MST

Swapping axes on a 1000x1500

Thu, 15 Oct 2020 07:58:32 -0700

Would I be able to convert a 1000x1500 kit to a 1500x1000 machine?

I'd like it to be wider and less deep.

⟐ Answer accepted October 15, 2020, 7:58 MST

The Wifi Module on my WorkBee is stuck in Idle Mode

Tue, 13 Oct 2020 01:46:29 -0700

The Wifi Module on my WorkBee is stuck in Idle Mode

⟐ Answer accepted October 13, 2020, 1:46 MST

What are the X, Y & Z-axis of the WorkBee?

Mon, 12 Oct 2020 06:03:12 -0700

What are the X, Y & Z-axis of the WorkBee?

⟐ Answer edited October 12, 2020, 6:03 MST

Can I use a 6mm endmill in my 1/4” collet?

Tue, 13 Oct 2020 01:08:37 -0700

Can I use a 6mm endmill in my 1/4” collet?

⟐ Answer edited October 13, 2020, 1:08 MST

Is the WorkBee compatible with Linux Operating systems

Mon, 12 Oct 2020 03:15:57 -0700

Is the WorkBee compatible with Linux Operating systems

⟐ Answer accepted October 12, 2020, 3:15 MST

What is the difference between Climb and Conventional cutting?

Tue, 13 Oct 2020 01:10:56 -0700

What is the difference between Climb and Conventional cutting?

⟐ Answer edited October 13, 2020, 1:10 MST

What is the difference between Up and Down Cut Endmills?

Tue, 13 Oct 2020 01:10:18 -0700

What is the difference between Up and Down Cut Endmills?

⟐ Answer edited October 13, 2020, 1:10 MST

limit switches are wired as show

Tue, 29 Sep 2020 08:13:04 -0700

Hi, I’m currently setting up my machine. The limit switches are all as pictured, however the status showed “Yes” switching to “No” when pressed. According to the set up procedure these should be “No” when not activated. The red lites on the Duet board are also all on. Please advise as I do not want to proceed to Home the machine until I’m sure. Thanks

⟐ Answered September 29, 2020, 8:13 MST