Ryan Christy

My Ethernet WorkBee will not connect to my computer and WorkBee Control will not load.

The Wifi Module on my WorkBee is stuck in Idle Mode

Is there only one height the Spoilerboard can be positioned?

Is the WorkBee compatible with Linux Operating systems

What is the difference between Climb and Conventional cutting?

What is the difference between Up and Down Cut Endmills?

What are the X, Y & Z-axis of the WorkBee?

Can I use a 6mm endmill in my 1/4” collet?

Hi Andy! In your Kit for the 1500x1500mm Version you will have 3 x 1557mm Lead Screws ( 2 for the Y-Axis and 1 for the X-Axis ) the shorter Lead-Screw 281mm is for the Z-Axis Assembly, If you do believe you have anything missing please get in touch here and we will be happy to look into it for you - https://ooznest.co.uk/help/

Ensure your Ethernet Adaptor settings match the Connect via Ethernet Guide for your version machine then proceed with the below: (1) Restart the PC that you are using as the Ethernet Connection setting may not have refreshed upon changing the IPv4 settings. (2) Disable the Ethernet adaptor and re-enable it by navigating to Control Panel > Network and Internet > Network. Right Click on the Ethernet Connection and Disable, wait a moment before re-enabling and refresh your Browser. (3) Clear the Browser Cache.

You should only need to connect via USB for Troubleshooting, not for the normal runnings of the machine. If you find that your IP Address is changing for your WorkBee if it is a Wifi Version you can make it static to ensure future connectivity. - If you are having issues please contact us here - https://ooznest.co.uk/help/#tab_technica...-support

Hi, Yes this is possible but it would require you to buy the components individually on our website. It is not a kit that we currently offer, but certainly do have all the parts to do so. You would need to replace items such as extrusions, motor wires and drag chains to fit your specific build.

If your Duet's Wifi Module is not responding in YAT or is stuck in Idle please try sending the following commands.   M552 S-1 = This will disable the WiFi module. Wait 10 Seconds M552 S0 = Disabling networking and put the Wifi Module in Idle Mode. Wait 10 Seconds M552 S1 = Enable networking and try to find your Wifi Network.

The WorkBee can be modified to have the spoiler board at different heights. This is achieved by increasing the distance between the bottom of the Z-Axis and the top of the spoiler board. The easiest way to gain extra cut depth is to attach a spoiler board, which is the same size as the machine footprint, to your Workbench. Then fix the machine on top of this Spoilerboard, and remove the spoiler board supports. If you originally had a 12mm spoiler board, this would gain you an extra 52mm of Z-Travel, this an extra 26mm of cut depth. Bringing the total cut depth to 73mm.

The WorkBee uses WorkBee Control. This is browser-based control software, and it is installed on the Duet Controller. More information about WorkBee Control can be found here: WorkBee Control Overview This will work from a Linux based Operating System although the software needed to generate both CAM and CAD operations will be extremely limited as most are Windows-based.

The difference between Conventional and Climb milling on a CNC machine can be quite confusing. Climb milling is generally used for the roughing pass and conventional for the finishing toolpath when surface finish is critical. Full details can be found by watching the video below on the Ooznest YouTube channel. https://www.youtube.com/watch?v=UQL8HeC7...

Downcut Endmills are best used for thinner materials which will be pushed down into the machine bed rather than being lifted with an up-cut spiral. Downcut spiral tools should be used when processing thin materials, 1/8” (3.175mm) or thinner. With this type of mill, you will achieve a high-quality cut finish on the top surface of cut parts. Upcut Endmills are the most popular type of fluted tool. You can use these for grooving or slotting, for upward chip evacuation. Beware that the upward force can pull the material causing a ragged finish on the top surface, or even worse, launch the part from the table. This will give the best finish on the bottom side of a part. These bits allow for rapid cuts since the tool clears the chips away from the material.  While ideal for cutting thicker materials, this type of tool is not recommended for thinner or softer materials.

The X, Y and Z-Axis are the directions the router head travels. The G-Code uses a coordinate system to make the cuts on your project. X - The direction of travel from left to right. Y - The direction of travel from the front to back. Z - The vertical axis which travels up and down. Here is a link highlighting the WorkBee CNC Machine’s axis: 4. Testing Your WorkBee

Hi Sam, Thanks for your feedback we will look into and revise the design to ensure this is resolved!

Hi Calum, If you have any issues with the lengths of wires please get in touch here - https://ooznest.co.uk/help/

Hi Alastair, I have changed the guide just in case anyone else comes to the same hurdle!

Hi Peter - You will have enough spares included in the Tee-Nuts Bag to complete the build. If you do find you need more please let us know by clicking here - https://ooznest.co.uk/help/ and we can get some sent out to you.

Thanks for spotting this mistake! - The Image has now been updated.

Hi Rob, If you find one is binding please double check it on the other Lead-Screw by hand to see if it is tight as it should turn freely.

Should it bind on the other Lead-Screw please get in touch here - https://ooznest.co.uk/help/#tab_technica... then we can arrange a replacement for you.

Hello Xander, Thanks for spotting this!

I have updated the guide it should be 1.5mm the smallest needed for the flexible coupler grub screws.

Hi Michael, All our guides for the WorkBee can be found hosted on this Learning Portal, they can also be downloaded into a PDF form should you wish to print them off, If you are stuck on any steps please feel free to get hold of us here - https://ooznest.co.uk/help/

Hi Bryan, Thanks for your message, Please see this link on how to update to the latest WorkBee Control - How To Update WorkBee Firmware

Hi Terry, It sounds like you may not have updated the WorkBee Control on your machine.

Are you able to email into Technical Support and we can look at what is causing your issues with the Touch Probe - https://ooznest.co.uk/help/#tab_technica...