Thanks.

⟐ Answered September 28, 2020, 2:35 MST

having trouble in machine control

i can set home and wrk coordinates

and use xyz touchprobe

after touchprobe goto wokzero and he bt dives into wood 10mm approx

m98 p"workzero.g"

go/g1: target position outside machine limts

g38.2 command not supported

please help

im new to all this

thanks barry

⟐ Answered September 24, 2020, 12:28 MST

Many thanks,

Phil.

⟐ Commented September 19, 2020, 2:14 MST

WorkBee v2.2

750x1000

Ethernet module

After connecting the Duet 2 via USB, and following the initial install guide carefully, I was able to get to the point of connecting to the web portal, upon which I was greeted with this:

At first I was not concerned due to the notice in the steps, but as I continued it did not match what I was expecting from the guide:

Can you spot it?

3. Connecting, Updating and Configuring Your WorkBee

I don’t have an upload button under general settings.

I attempted to use the file manager/system page listed on left to upload the firmware and it recognized the file as a firmware update, proceeding to load and reboot, but the interface did not change.

Further on, trying to enable my touch probe lead to related problems as the component to enable it does not exist on my interface. Even after uploading “DuetWifiServer.bin” as directed by @ryanlock on my comment on WorkBee Firmware Releases about the missing interface component and general lack of interface alterations required to match the hardware as sold did nothing to remedy the situation.

Does anyone have a known good image of the SD card for firmware version 1.0.7, duet 2 pcb revision 1.04c that I can flash my SD card with to resolve this issue?

Also, can someone please tell me why this text has gotten my posts deleted twice now?

⟐ Commented September 19, 2020, 2:05 MST

i keep getting a eror g0/g1 target outside machine limits every time i run my machine . it positions my router to the carving start point but will not plunge and run. im not a great tecnical person so alll help would be appreciated.

⟐ Answered September 19, 2020, 2:04 MST

⟐ Answered September 17, 2020, 12:38 MST

Do you have a recommended method/SSR for automatically starting the Makita router directly from the Duet2?

Thanks

Rich.

⟐ Answer accepted September 16, 2020, 13:39 MST

Thanks for your help!

⟐ Commented September 15, 2020, 8:17 MST

when routing the wire as directed the wires are held higher than the x-axis c-extrusion by the strain relief off of the z-axis limit switch causing them to contact the beam and will lead to either friction causing a short circuit or the repetitive strain on the wires causing metal fatigue failure in either the wire itself, the switch terminals, or in the solder joint between the two.

Is there any work being done to resolve this issue, or an alternate wire path that avoids these problems? And if there is an alternative wire path, where can I find it?

⟐ Commented September 14, 2020, 2:30 MST

⟐ Answer accepted September 10, 2020, 1:15 MST

⟐ Answer accepted September 09, 2020, 12:59 MST

⟐ Answer accepted September 09, 2020, 7:47 MST

Is there anything specific needed for this on the mobile or just the IP address in the browser on the phone?

We have a ethernet only workbee which is all connected OK but the PC does have a USB wifi adaptor.

⟐ Answered September 09, 2020, 0:44 MST

Is this possible?

⟐ Answered September 08, 2020, 8:03 MST

⟐ Answered September 07, 2020, 1:17 MST

⟐ Answer accepted September 04, 2020, 10:21 MST

⟐ Answered August 27, 2020, 1:07 MST

⟐ Answer accepted August 25, 2020, 0:10 MST

⟐ Answered August 19, 2020, 10:28 MST

Thanks,

Phil.

⟐ Commented August 18, 2020, 1:40 MST