Skip to main content

{{release_title}}

Minor Versionm

by Dozuki System

Introduction

Be very careful to not over tighten the nuts and bolts on the plastic parts, otherwise they

may crack. Everything should easily fit together, and so if it isn’t, take a step back and

re-read the instructions.

  1. If the wires in your kit have white printed tags, please ignore this step. Each wire, at the connector end has a coloured clip with a number. This colour and number identifies this wire. Please see key below.
    • If the wires in your kit have white printed tags, please ignore this step. Each wire, at the connector end has a coloured clip with a number. This colour and number identifies this wire. Please see key below.

    • (0)(Black) X-Axis Limit Switch

    • (1)(Brown) Y-Axis Limit Switch

    • (2)(Red) Z-Axis Limit Switch

    • (3)(Orange) X-Axis Stepper Motor Wire.

    • (4)(Yellow) Left Y-Axis Stepper Motor Wire.

    • (5)(Green) Right Y-Axis Stepper Motor Wire.

    • (6)(Light Blue) Z-Axis Stepper Motor Wire.

  2. Please see the key in Step 1 for Wire Identifications, the Limit Switches are pre-attached to the Switch Wires. Carefully attach the (0)(Black) X-Axis Limit Switch to the X-Axis Limit Switch Mount using 2 x M3 Plastite Screw - 8mm's. The M3 Plastite Screw - 8mm's self thread, the best technique is to screw in a couple of turns, then back out, and then back in a few more turns than last time, and so forth, until the Limit-Switch is firmly secured.
    • Please see the key in Step 1 for Wire Identifications, the Limit Switches are pre-attached to the Switch Wires.

    • Carefully attach the (0)(Black) X-Axis Limit Switch to the X-Axis Limit Switch Mount using 2 x M3 Plastite Screw - 8mm's. The M3 Plastite Screw - 8mm's self thread, the best technique is to screw in a couple of turns, then back out, and then back in a few more turns than last time, and so forth, until the Limit-Switch is firmly secured.

    • A PZ1 screwdriver would be preferred to use on the plastite scews.

    • Do not over tighten as you can shatter the switch. Make sure the Limit-Switch is orientated as the X-Axis-Limit-Switch-Assembly picture.

    • Attach a M5 Low Profile Bolt - 8mm through the elongated hole and slightly thread on a M5 Drop In Tee Nut.

    • Attach the X-Axis Limit Switch Mount assembly to the back side of the X-Axis C-Beam. It should be oriented as the second picture, on the far left hand side (If looking from the back of the machine). The X-Axis Limit Switch Mount should be touching the Y-Plate.

    • Tighten the M5 Low Profile Bolt - 8mm bolt, engaging the M5 Drop In Tee Nut with the top slot of the X-Axis C-Beam.

  3. Please see the key in Step 1 for Wire Identifications, the Limit Switches are pre-attached to the Switch Wires. Carefully attach the (1)(Brown) Y-Axis Limit Switch to the Y-Axis Limit Switch Mount using 2 x M3 Plastite Screw - 8mm's. The M3 Plastite Screw - 8mm's self thread, the best technique is to screw in a couple of turns, then back out, and then back in a few more turns than last time, and so forth, until the Limit-Switch is firmly secured. A PZ1 screwdriver would be preferred to use on the plastite scews.
    • Please see the key in Step 1 for Wire Identifications, the Limit Switches are pre-attached to the Switch Wires.

    • Carefully attach the (1)(Brown) Y-Axis Limit Switch to the Y-Axis Limit Switch Mount using 2 x M3 Plastite Screw - 8mm's. The M3 Plastite Screw - 8mm's self thread, the best technique is to screw in a couple of turns, then back out, and then back in a few more turns than last time, and so forth, until the Limit-Switch is firmly secured.

    • A PZ1 screwdriver would be preferred to use on the plastite scews.

    • Do not over tighten as you can shatter the switch. Make sure the Limit-Switch is orientated as the Y-Axis-Limit-Switch-Assembly picture.

    • Attach a M5 Low Profile Bolt - 8mm through the elongated hole and slightly thread on a M5 Drop In Tee Nut.

    • Attach the Y-Axis Limit Switch Mount assembly to the back side of the Right Y-Axis C-Beam (If looking from the back of the machine). It should be oriented as the third picture. The Y-Axis Limit Switch Mount should be touching the Y-C Beam Extrusion.

    • Tighten the M5 Low Profile Bolt - 8mm bolt, engaging the M5 Drop In Tee Nut with the top slot of the Y-Axis C-Beam.

  4. At this stage of the guide review your machine and guide pictures to ensure correct installation. Your finished assemblies should look like the pictures once completed.
    • At this stage of the guide review your machine and guide pictures to ensure correct installation.

    • Your finished assemblies should look like the pictures once completed.

  5. Please see the key in Step 1 for Wire Identifications, the Limit Switches are pre-attached to the Switch Wires. Attach the (2)(Red) Z-Axis Limit Switch to the threaded holes on the X-Plate-Front using 2 x M3- Button-Head-10mm bolts, in the same orientation as the picture.
    • Please see the key in Step 1 for Wire Identifications, the Limit Switches are pre-attached to the Switch Wires.

    • Attach the (2)(Red) Z-Axis Limit Switch to the threaded holes on the X-Plate-Front using 2 x M3- Button-Head-10mm bolts, in the same orientation as the picture.

    • Do not over tighten as you can shatter the switch. Make sure the Limit-Switch is orientated as the Z-Axis-Limit-Switch-Assembly picture.

Conclusion

Thanks for following the guide. Any issues, please contact us!

34 other people completed this guide.

Robert

Member since: 12/03/2018

13,909 Reputation

104 Guides authored

One Comment

The access to the z limit should be rethought.

Wires exposed and difficult to get to when it needs to be fixed.

Oscar - Reply

Add Comment

View Statistics:

Past 24 Hours: 2

Past 7 Days: 8

Past 30 Days: 34

All Time: 3,527