got a new duet 2 wifi controller which guide do I use, not sure if this one has firmware for 3d printers on it, how do I flash it with the correct workbee firmware?
Is this a good question?
Hi Brian,
Download this zip: https://we.tl/t-VSUzQibMN0
Extract the contents, and then put the contents on a blank SD Card.
These are the files for a 750x750 Wifi WorkBee running a similar firmware version to you.
If you can get connected, then complete this guide: How To Update WorkBee Firmware V1.0.7 > V3.3.0-1.2
Robert
Was this answer helpful?
Hi Brian,
Thanks I see, if you get connected via USB following this guide: 1. Connecting your Controller via USB - Windows
Once connected, send the command M408 S5 and then send me the result please.
Was this answer helpful?
Hi Thanks for the reply, here is the result from M408 S5
{"axisMins":[0.00,0.00,0.00],"axisMaxes":[200.00,200.00,200.00],"accelerations":[500.00,500.00,20.00,250.00,250.00,250.00,250.00,250.00,250.00,250.00,250.00,250.00],"currents":[0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00,0.00],"firmwareElectronics":"Duet WiFi 1.02 or later","firmwareName":"RepRapFirmware for Duet 2 WiFi/Ethernet","firmwareVersion":"2.03beta3","dwsVersion":"(unknown)","firmwareDate":"2019-03-25b6","idleCurrentFactor":30.0,"idleTimeout":30.0,"minFeedrates":[15.00,15.00,0.20,2.00,2.00,2.00,2.00,2.00,2.00,2.00,2.00,2.00],"maxFeedrates":[100.00,100.00,5.00,20.00,20.00,20.00,20.00,20.00,20.00,20.00,20.00,20.00]}<LF><LF>ok<LF>
Hi Brian,
Follow these 2 guides to get connected via Wifi:
1. Connecting your Controller via USB - Windows
2. Connecting your Controller to a Network - Wifi
And then can you try and complete this guide here: How To Update WorkBee Firmware V1.0.7 > V3.3.0-1.2
Guide
Difficulty:
Easy
—
5 - 10 minutes
Guide
Difficulty:
Easy
—
5 - 10 minutes
Guide
Difficulty:
Moderate
Was this answer helpful?
Hi Thanks again for your reply. I have been able to connect to the duet using YAT. The controller has assigned an IP address so that part works fine. But please keep in mind, I’m a complete noob and when I try and load the Url http://workbee.local/ it just shows page cannot be displayed in my browser. Should I have installed the workbee control software to my PC or something? Also Just a quick after thought, I don't have a memory card installed. Does the duet need something on a micro SD card?
Brian, instead of putting http://workbee.local/ , try putting the IP address that you got from YAT into the address bar.
Was this answer helpful?
Hi, Thanks for the reply. I typed the ip address into my browser and i get this message
"Your Duet rejected the HTTP request: page not found Check that the SD card is mounted and has the correct files in its /www folder"
This must suggest that it is looking For a SD card, I never received an SD card with the duet. my question now is, I have a spare formatted one (Fat32) what do I need to put onto the SD card
Hi Brian,
Thanks for your email.
Do you have an Order ID with us so I can see which one you bought and check this?
Was this answer helpful?
Sorry bit of confusion, I didn’t get the duet 2 wifi from you, but the Workbee was from you. The workable was a kit bought by my boss a long time ago (maybe one of the first you had) and was gifted to me part built but practically brand new. I broke the Xpro 3 controller with a stupid mistake and purchased a duet 2 just to hopefully get this machine working. and will be upgrading as and when I finally have it fully cutting.
Was this answer helpful?
Thank you so much, I have now successfully updated and connected to the Duet, all I needed was a SD card with the right files on it. I have now been Able to upgrade to the latest firmware, Now to fully test all the rest of the machine and hopefully complete the first project guide over this weekend. Big thanks for all who helped me and a massive thanks to Robert at Ooznest.
Was this answer helpful?
Hi Brian,
Glad you got it sorted!
Past 24 Hours: 0
Past 7 Days: 3
Past 30 Days: 7
All Time: 345
