Answers Forum - Ooznest

Learn How It Works Ask a Question

All Questions

1 Answer

Failed to enable endstops G28 X

1 Answer

Robert 24.3k

Answered

Oct 4, 2021

Answered Oct 4, 2021 by Robert

1 Reply

Getting an uneven bottom section on large pockets

discussion 1 Reply

Robert 24.3k

Commented

Oct 1, 2021

Commented Oct 1, 2021 by Robert

1 Reply

Updating workbee Duet2 with firmware from Duet3D

discussion 1 Reply

Robert 24.3k

Commented

Sep 23, 2021

Commented Sep 23, 2021 by Robert

1 Answer

1500x1500 assembly instructions v2.3 for spoiler board support

1 Answer

Robert 24.3k

Answered

Sep 22, 2021

Answered Sep 22, 2021 by Robert

1 Answer

1500x1500 assembly instructions v2.3

accepted 1 Answer

Answer accepted

Sep 15, 2021

Answer accepted Sep 15, 2021 by Steve Jenks

1 Reply

Sudden workbee fault issue

discussion 1 Reply

Robert 24.3k

Answered

Sep 8, 2021

Answered Sep 8, 2021 by Robert

1 Reply

What GCode dialect does the Ooznest workbee use?

discussion 1 Reply

Robert 24.3k

Commented

Sep 1, 2021

Commented Sep 1, 2021 by Robert

1 Answer

Can I add bigger spindle

1 Answer

Robert 24.3k

Answered

Aug 31, 2021

Answered Aug 31, 2021 by Robert

2 Answers

Can not connect to YAT via cable

2 Answers

Robert 24.3k

Commented

Aug 31, 2021

Commented Aug 31, 2021 by Robert

2 Answers

'G2/G3: Outside Machine Limits' error

accepted 2 Answers

Robert 24.3k

Commented

Aug 24, 2021

Commented Aug 24, 2021 by Robert

1 Reply

finding the duet controller directly panel where do I find or download

discussion 1 Reply

Robert 24.3k

Answered

Aug 23, 2021

Answered Aug 23, 2021 by Robert

2 Answers

How do I get into the control panel to operate the machine?

2 Answers

Answered

Aug 20, 2021

Answered Aug 20, 2021 by bryan robbins

1 Answer

How do Tool (Endmill) changes happen on the WorkBee?

accepted 1 Answer

Robert 24.3k

Commented

Aug 16, 2021

Commented Aug 16, 2021 by Robert

1 Answer

Outside Machine Limits - zaxis

1 Answer

Robert 24.3k

Commented

Aug 9, 2021

Commented Aug 9, 2021 by Robert

1 Answer

How many Y-ACME-Lead-Screw are in kit

1 Answer

Commented

Aug 2, 2021

Commented Aug 2, 2021 by Andrew C

1 Answer

My Ethernet WorkBee will not connect?

accepted 1 Answer

Ryan Christy 31.4k

Answer accepted

Aug 2, 2021

Answer accepted Aug 2, 2021 by Ryan Christy

1 Reply

V11 upgrade gcode post processor?

discussion 1 Reply

sdsmith@ropley.com

Commented

Jul 27, 2021

Commented Jul 27, 2021 by sdsmith@ropley.com

1 Answer

Does the Workbee come with a serial number?

1 Answer

Robert 24.3k

Answered

Jul 26, 2021

Answered Jul 26, 2021 by Robert

1 Answer

Machine bed size upgraded but how do I increase it in the software?

1 Answer

Robert 24.3k

Commented

Jul 26, 2021

Commented Jul 26, 2021 by Robert

1 Answer

Can you use the XYZ-probe with an engraving bit?

1 Answer

Robert 24.3k

Answered

Jul 23, 2021

Answered Jul 23, 2021 by Robert

Page 18