Completed Guides
Questions
-
Set X and Y in a Macro?Hello, I’m looking for a way to Set X and Y in a Macro, just like when SET X and SET Y are pushed. Which code should I use...
-
Offset Difference between TouchProbe and Center marksHello, I have an offset problem when I Probe corners with the touch probe; (1) If I mark a cross on a square piece, and I...
-
Thrust Bearing Kit worth it?Hello, I have an Original Workbee 1000X1000 bought in early 2021, and there’s a possible upgrade with the Thrust Bearing...
-
Dimensions mismatch Pocket / ContourHello, I have a weird problem that I can’t figure out, after calibrating X steps/mm, if I pocket a square of 40mm the...
-
How to avoid Tenons MarksHello, I know it’s not very relative to the Workbee, but I’m struggling to find a solution to avoid tenon marks during...
-
Laser Kit for Workbee?Hello, Is there any possibility to add a Laser Kit to Workbee (1000X1000) ? I’m looking for a non expensive product, not...
-
How to reset Work Coordinate Selection Presets?Hello, Is it possible to reset, meaning emptying the several Work Coordinate Selection Presets 1 to 9, I can’t see any...
-
Impossible to Calibrate Y AxisHello, I have issues calibrating Y Axis on a 1000x1000, I followed the Step/mm Guide, reporting correct values in...
Answers
-
Answer to "4th axis Rotary atatchement"Hello, Have you by any chance gone forward with your project ? I’m also interested, but I’m confused with the addition of additional axis in configuration. Thanks Guillaume
-
Answer to "Offset Difference between TouchProbe and Center marks"Thanks for you answer, I will re check calibration to see if it’s ok with this Guillaume
-
Answer to "Set X and Y in a Macro?"Thanks for the tip Robert
-
Answer to "Offset Difference between TouchProbe and Center marks"Hi Robert, At least 1mm on small dimensions, growing in bigger pieces. If I modify th etouch probe settings could I correct that ? Thanks Guillaume
-
Answer to "Thrust Bearing Kit worth it?"Thanks Robert, there is two version available, is a Workbee from Feb 2021 is V 2.3 or V 2.1 ? Thanks Guillaume
-
Answer to "Dimensions mismatch Pocket / Contour"Hi Robert, No, everything is straight on CAM side. Thanks Guillaume
-
Answer to "Dimensions mismatch Pocket / Contour"Hi Robert, Thanks for help. So calibrated again using a contour, which is ok, and I’ve done a pocket of same dimensions on these settings, with the correct endmill value, and I still have a 0.60mm difference (positive in the pocket) between these toolpaths. I guess at this point I can do nothing more to improve that. Thanks Guillaume
-
Answer to "Dimensions mismatch Pocket / Contour"Hi Robert, I'm using a 6mm endmill, which is actually 5.96 with a digital caliper. Is these 0.04 are accounting, I guess so. When you are calibrating, is it better using a contour or a pocket to calibrate ? Thanks for your help Guillaume
-
Answer to "How to avoid Tenons Marks"Hello Robert, Yes indeed it’s tabs sorry for my english, I’m currently using Vcarve toolpaths, haven’t tried with Fusion yet, Vcarve is doing the job for the rest, the only reccurent problem that I have is these tabs marks, even with 3D tabs, during contour. I tried several types of 3.17mm end-mills. Please finf pictures attached. Thanks a lot for help. Best Guillaume
-
Answer to "Impossible to Calibrate Y Axis"Hi Robert, I’ve made a new test, on 3x 40x40 Squares, and from right to left: (1) Square 1 is X40.45 and Y 40.30 (2) Square 2 is X40.40 and Y 40.30 (3) Square 3 is X40.38 and Y 40.30 Each time I modify settings, I’m under or over 40, never exactly 40. However, I’m using MDF for the tests, and I guess it’s not very accurate for testing. My tests are made with a 3.17mm Endmill. Thanks very much for your help Best Guillaume
Guide Comments
Reputation over time
Reputation Breakdown
Event | Count | Delta |
---|---|---|
Accepted answer | 5 | 50 |
807
Hello,
I just ordered a 1000X1000 model, and I’m struggling a little bit to understand exactly the possible cut depth allowed in 47mm. If I use a 20mm spoilerboard mounted on original spoilerboard support, what is the cut depth left ?
Thanks
Guillaume